Cockpit Gauges Q&A

Cockpit Gauges Q&A

Answers to common questions about choosing, installing and configuring FPVToys cockpit gauges. Start with the equipment already in your model and whether you want live telemetry or simulated instruments.

Choosing your equipment · Telemetry and simulation · Setup and firmware · Display options · Getting help

Choosing your equipment

What do I need to buy?

You need a gauge controller and the screens you want. The controller includes the selected flight-controller connection cable; screens are sold separately. For live readings, you also need a supported telemetry source.

How many screens can one controller run?

One controller runs up to four screens. You can mix screen sizes and configure each screen differently.

Can I connect a screen directly to my flight controller?

No. The gauge controller drives the screens and draws the instruments.

Which screen size should I choose?

Check both the visible display area and the overall circuit-board dimensions on the Display Specifications page. If you need help choosing, send the space available in your cockpit and what you want displayed.

Can you set up the screens before shipping?

Yes. Request preconfiguration in the checkout comments. List the screen size for each controller port and what you want it to display. You may still need to adjust rotation for your installation and configure your telemetry source.

Telemetry and simulation

Do I need a flight controller?

Not for every setup. MSP and MAVLink use flight-controller data. SmartPort can use available sensor telemetry from a compatible receiver and sensors. SBUS and direct RC inputs drive simulated instruments. A static model can run the automatic demo without external input. See Input Sources.

Which input should I use?

Use MSP for most iNav and Betaflight installations, or MAVLink for ArduPilot. SmartPort is an option with suitable FrSky telemetry sensors. SBUS uses four primary RC channels for simulation; direct RC uses aileron and elevator. The input guide explains each connection and command.

Are SBUS or direct RC readings measured flight data?

No. These modes estimate the instruments from your control inputs. For measured readings, use a telemetry source that supplies the required data. Direct RC inputs must be 3.3 V, not 5 V.

Will it work with my radio or stabilized receiver?

Send the exact receiver model and any flight controller or telemetry sensors you use. The radio brand alone does not identify the data available to the gauges. A receiver having stabilization does not necessarily mean its gyro data is available to other equipment.

Does the flight controller have to control my airplane?

It can be installed just to supply instrument data. The available readings depend on its firmware, sensors and connections. Do not assume it can read sensors intended for a different telemetry system.

Can I share the MSP connection used by my video system?

The gauge controller is designed to use its own flight-controller serial port. MSP uses requests and responses. Listening to an existing video-system connection may provide some messages, but it is not a guaranteed replacement for a dedicated port.

Can I use the gauges in a static model?

Yes. Firmware 1.15 and later include an automatic flight demo. With no external input connected, enable Simulator in the keypad menu or enter sim on, then save. The flight instruments and map animate without a receiver, GPS or flight controller. Use sim off for live flight-controller telemetry. See automatic demo setup.

Setup and firmware

What is the easiest way to configure the controller?

With firmware 2.0, use the Controller Configurator over USB in desktop Chrome on Windows, macOS or Linux. Read the controller, make changes, choose Apply changes, then Save to controller. You can also use a serial terminal or the optional setup keypad.

Do I need the internet or Wi-Fi to configure it?

USB configuration does not require controller Wi-Fi. Keep a downloaded copy of the configurator for offline use. Online map imagery and reference pictures need internet access. See the configurator instructions.

Which firmware should I use?

Firmware 2.0 is the current recommended release. The USB configurator requires 2.0. Existing controllers receive these features through a normal firmware update; no replacement controller is needed. Follow the upgrade notes and check your settings afterward.

How do I save settings and map changes?

In firmware 2.0, save or save all stores both settings and map data. Use save settings for settings only, or save map / map save for map data only. In firmware 1.15 and earlier, save settings with save and maps separately with map save. In the configurator, Apply changes does not save them across power-off; use Save to controller.

Which cable should I choose?

Match the exact flight-controller port and its wiring, not just the connector size. The cable guide covers .1-inch headers, 6-pin GH telemetry ports, and the different 4-pin GH layouts. RadioMaster Nexus and Roban / Orqa layouts are different. If unsure, send the board model, revision and a photo of the port.

Why does my computer not show a serial port?

Use a data-capable USB cable; charge-only cables will not work. Try another USB port and close any other terminal or configurator using the connection. On Windows, check Device Manager for the device that appears when you plug in the controller. See Troubleshooting.

Why is a screen blank or showing the wrong image?

Check cable orientation and select the driver matching that display chip and resolution. Check driver ? on your installed firmware; driver numbers changed in 1.15. Select the physical display first with display 1, display 2, and so on. Custom cable views can look mirrored from opposite ends, so confirm the board markings and wiring diagrams.

Can I add airports, waypoints and runways?

Yes. Use the combined Map Tool to prepare entries, or use map editing and command import in the configurator. Firmware 2.0 supports 50 airports, 50 waypoints and 200 runways. Keep a configuration backup before large map changes.

Display options

What can each screen show?

Choose from G1000, Map, PFD, MFD, Airport Diagram, configurable Split Screen, FMC, Radio Stack, HUD and traditional instruments. Screens can use different modes. Weather radar is simulated; the radio-stack view is static. Aircraft radar can use supported traffic sources or simulation. See Display Modes.

Can I resize and position the instruments?

Yes. Instrument scale and spacing are configurable per display. The number that fits depends on resolution, rotation, size, spacing and the area available in a split view. The keypad provides scale and spacing controls; see the CLI reference for the complete options.

Can I build a heads-up display?

HUD mode uses the supported screens, with a mirror or reflector arrangement built for your cockpit. Select mode h and use mirroring when required. See Display Modes and the customer examples on User Installs.

Can I use my own startup logo or a static image?

Firmware 2.0 supports uploaded PNGs as per-display startup logos or static images. Use Prepare an image and Controller files in the configurator. Back up image files separately from the configuration.

Why are the instruments blurry through my FPV camera?

The camera needs to focus on nearby instruments as well as the view outside. Lens choice and depth of field matter, and a lens that works with one camera may not fit another. Send your camera model and its distance from the panel if you need help.

Does using more screens affect refresh speed?

Yes. The number of active screens and what they display affect refresh speed. For flicker or corrupted graphics, check wiring and power, then follow the display guidance in the CLI reference and Troubleshooting.

Getting help

Where can I see completed installations?

Visit User Installs for customer cockpit layouts and videos.

What should I include when asking for help?

Send your firmware version, screen sizes and driver settings, selected input type, flight-controller model and firmware if used, receiver model, and a description of the problem. Wiring photos and a copy of the settings are useful. Contact FPVToys.

Shopping Cart